Let It Snow Machine, supports an artificial tree up to
7 1/2 feet in height.
Comes with 1 Bag of Snow
(Tree Not Included).
In Stock! Shipping Now...
$199.95
Pictures of Snowing Machine Un-boxing and Assembly
Snowing Machine Snowing In Action!
Replacement Parts for your Snowing Machine
Item Sku: 09051
Extra Bag of Snow for Snow Machine
Approximately 2 lbs, 1.5 cubic feet
$59.00
Item Sku: 09040BOX
Snowing Machine Box with Gussets
Replacement for your snowing machine box and gussets.
Disclaimer: Please note that over time designs may change, and
some parts may need to be slightly resized, taped, sealed, glued,
or otherwise adjusted to enable old parts to convert or fit with
the new parts.
Item Sku: 09040MOTOR
Snowing Machine Motor with Transformer
Replacement for your snowing machine motor and transformer.
Disclaimer: Please note that over time designs may change, and
some parts may need to be slightly resized, taped, sealed, glued,
or otherwise adjusted to enable old parts to convert or fit with
the new parts.
$59.00
$59.00
Item Sku: 09040PIPE
Snowing Machine Piping Kit
Replacement piping kit for your snowing machine.
Disclaimer: Please note that over time designs may change, and
some parts may need to be slightly resized, taped, sealed, glued,
or otherwise adjusted to enable old parts to convert or fit with
the new parts.
The Snowing Machine will give the
appearance “it’s actually snowing”.
The decorative box opens up to catch the falling snow and then
recycles the snow.
You can cover the edge of the box with fabric or Christmas paper for
a more decorative look as noted in the picture above.
Your tree stand must not exceed 24 inches. We recommend using a 7 ˝
foot tall slim artificial tree. A larger tree may require an extra
bag of snow as more snow will accumulate on a larger tree.
Contents: 1-Bag Artificial Snow, 3-Green Tubes & 3 Ties, 1-Flex
Hose, 1-Venturi (plastic pipe with opening on side attached to the
foam housing box.), 1-Motor Housing W/Blower Motor Attached To The
Inside Of Box, a transformer that plugs into the connector in the
outside opening in the box. (TREE NOT INCLUDED)
You Can Use The Blower Machine For All Holidays
Setting Up the Snowing Machine
1. The four "gussets" form the box, place them where you want and
remove the backing from the Velcro to secure them to the green
box...you can make the box "more vertical" or "more horizontal" as
you wish. The base box dimensions are 24” x 24” x 8”, which opens up
to a maximum of a 48” diameter and a depth of 18”. You'll be able to
dissemble at the end of the season.
2. Place your tree (or other object) in the container.
3. You may want to cut some pieces of cardboard and tape in place in
the corners of the box and around the tree stand to direct the snow
to the venturi, where the snow enters the piping system. This saves
on the amount of snow needed. Due to all the many different sizes
and shapes of tree stands this is left up to the individual, do this
before setting the tree in place.
4. Connect the 3 rigid green pipes and place them up the center of
the tree "or other object."
5. Attach the flexible green tube to the rigid pipes- AVOID A SHARP
BEND (the venturi should be pointing down).
6. Pour in the snow.
7. Connect the transformer...it's the electrical power supply.
8. Sit back and watch it snow.
Static and The Snowing Machine -
We treat many of the components with anti-static material so it
should not be a problem, but if it is, one or more of the following
will be a cure:
~Allow the machine to blow snow out of the flexible green tube
for a few minutes before connecting the rigid tubes.
~Spray "static guard" in the rigid pipes or pull a dryer sheet
through them.
~Lightly mist water on the snow.
New Base Design and Color!
snow machine, artificial snow, snowing machine,
snowing Christmas tree
To register for Christmas Treasures email updates on your favorite product
lines!
